Please Whitelist This Site?

I know everyone hates ads. But please understand that I am providing premium content for free that takes hundreds of hours of time to research and write. I don't want to go to a pay-only model like some sites, but when more and more people block ads, I end up working for free. And I have a family to support, just like you. :)

If you like The TCP/IP Guide, please consider the download version. It's priced very economically and you can read all of it in a convenient format without ads.

If you want to use this site for free, I'd be grateful if you could add the site to the whitelist for Adblock. To do so, just open the Adblock menu and select "Disable on tcpipguide.com". Or go to the Tools menu and select "Adblock Plus Preferences...". Then click "Add Filter..." at the bottom, and add this string: "@@||tcpipguide.com^$document". Then just click OK.

Thanks for your understanding!

Sincerely, Charles Kozierok
Author and Publisher, The TCP/IP Guide


NOTE: Using software to mass-download the site degrades the server and is prohibited.
If you want to read The TCP/IP Guide offline, please consider licensing it. Thank you.

The Book is Here... and Now On Sale!

Read offline with no ads or diagram watermarks!
The TCP/IP Guide

Custom Search







Table Of Contents  The TCP/IP Guide
 9  TCP/IP Lower-Layer (Interface, Internet and Transport) Protocols (OSI Layers 2, 3 and 4)
      9  TCP/IP Internet Layer (OSI Network Layer) Protocols
           9  TCP/IP Routing Protocols (Gateway Protocols)
                9  TCP/IP Interior Routing Protocols (RIP, OSPF, GGP, HELLO, IGRP, EIGRP)
                     9  TCP/IP Routing Information Protocol (RIP, RIP-2 and RIPng)
                          9  RIP Fundamentals and General Operation

Previous Topic/Section
RIP General Operation, Messaging and Timers
Previous Page
Pages in Current Topic/Section
1
234
Next Page
RIP Special Features For Resolving RIP Algorithm Problems
Next Topic/Section

RIP Protocol Limitations and Problems
(Page 1 of 4)

The simplicity of the Routing Information Protocol is often given as the main reason for its popularity; I certainly have mentioned this enough times in this section. Simplicity is great most of the time, but an unfortunate “price” of simplicity in too many cases is that problems crop up, usually in unusual cases or special situations. And so it is with RIP: the straight-forward distance-vector algorithm and operation mechanism work well most of the time, but they have some important weaknesses. We need to examine these problems to understand both the limitations of RIP and some of the complexities that have been added to the protocol to resolve them.

Problems With RIP’s Basic Algorithm and Implementation

The most important area where we find serious issues with RIP is with the basic function of the distance-vector algorithm described earlier in this section, and the way that messages are used to implement it. The are four main problems here: slow convergence, routing loops, “counting to infinity” and “small infinity”.

Slow Convergence

The distance-vector algorithm is designed so that all routers share all their routing information regularly. Over time then, all routers eventually end up with the same information about the location of networks and which are the best routes to use to reach them. This is called convergence. Unfortunately, the basic RIP algorithm is rather slow to achieve convergence. It takes a long time for all routers to get the same information, and in particular, it takes a long time for information about topology changes to propagate.

Consider the worst-case situation of two networks separated by 15 routers. Since routers normally send RIP Response messages only every 30 seconds, a change to one of this pair of networks might not be seen by the router nearest the other one until many minutes have elapsed—an eternity in networking terms.

The slow convergence problem is even more pronounced when it comes to the propagation of route failures. Failure of a route is only detected through the expiration of the 180-second Timeout timer, so that adds up to three minutes more delay before convergence can even begin.

Routing Loops

A routing loop occurs when Router A has an entry telling it to send datagrams for Network 1 to Router B, and Router B has an entry saying that datagrams for Network 1 should be sent to Router A. Larger loops can also exist: Router A says to send to B, which says to send to C, which says to send to A.

While under normal circumstances these loops should not occur, they can happen in special situations. RIP does not include any specific mechanism to detect or prevent routing loops; the best it can do is try to avoid them.


Previous Topic/Section
RIP General Operation, Messaging and Timers
Previous Page
Pages in Current Topic/Section
1
234
Next Page
RIP Special Features For Resolving RIP Algorithm Problems
Next Topic/Section

If you find The TCP/IP Guide useful, please consider making a small Paypal donation to help the site, using one of the buttons below. You can also donate a custom amount using the far right button (not less than $1 please, or PayPal gets most/all of your money!) In lieu of a larger donation, you may wish to consider purchasing a download license of The TCP/IP Guide. Thanks for your support!
Donate $2
Donate $5
Donate $10
Donate $20
Donate $30
Donate: $



Home - Table Of Contents - Contact Us

The TCP/IP Guide (http://www.TCPIPGuide.com)
Version 3.0 - Version Date: September 20, 2005

© Copyright 2001-2005 Charles M. Kozierok. All Rights Reserved.
Not responsible for any loss resulting from the use of this site.